The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
Nafaa Mekhilef, Gilberto O. Pasquariello, May 2006
The structure-rheology relationship is investigated in three polyethylenes namely high density polyethylene (HDPE), a metallocene linear low density polyethylene with no chain branching (mLLDPE) and a metallocene polyethylene containing long chain branching (mLLDPE-LCB). Shear and extensional rheology measurements were carried out in the linear viscoelastic regime and correlated to the molecular weight, molecular weight distribution and long chain branching. Shear rheology showed that HDPE exhibits a viscosity profile whereby the Newtonian behavior is not completely attained as shown by the slope of the storage modulus in the terminal region. mLLDPE was found to possess the longest and well-defined Newtonian region and the highest transition to the non-Newtonian region. In the presence of long chain branching (LCB), the terminal region is not apparent while the onset of shear thinning is decreased. Such behavior can be related to the effects of MWD and LCB and was corroborated using extensional viscosity measurements, which showed slight deviation from the LVE envelope for broader molecular weight distribution and strain hardening in the presence of long chain branching.
Nafaa Mekhilef, Gilberto O. Pasquariello, Paul Lavallee, Mark Lavach, May 2006
In this study the effect of acrylic-based components, including process aids (PPA), on the rheological properties of rigid PVC formulation is investigated. A statistically designed experiment was set up to cover the effect of composition on the melt viscosity and the melt strength of the compound as a function of temperature. The effect of the acrylic components was studied in relation to the rheological properties such as capillary rheometry and melt strength. In the absence of an acrylic process aid, the PVC compound showed a loss of adhesion at the wall caused by a change in the microstructure and characterized by pressure oscillations and a dip in the melt strength trace. As the temperature is increased, the slippage appears to be minimized and the head pressure stabilized.
The melt rheological properties of an ethylene/alpha-olefin copolymer polymerized by a supported metallocene catalyst, which have been developed as the easy processing polyethylene by Sumitomo Chemical, were evaluated and compared with conventional polyethylenes. The melt viscoelastic properties of the copolymer exhibit a shear rate dependence similar to that of high-pressure low density polyethylene that is considered to be caused by the wide molecular weight distribution and long chain branched molecular structure.In the latter part of this presentation, we have focused on the performance of the above copolymer. This copolymer exhibited superior processability in the fabrication of blown film such as low temperature and high output processing, leading to the production of a clean film without any additives and with low odor and taste.
Zhongbao Chen, A. Jeffrey Giacomin, Lih-Sheng Turng, May 2006
Flash, a common injection molding defect, arises when melt flows from the cavity into thin gaps between parting surfaces. Besides rules of thumb for eliminating flash, there are few fundamental papers on flash analysis. Understanding flash as a transport phenomenon provides a systematic basis for solving flash problems. The governing equations for the gap flow are established and solved for an isothermal power law fluid, under constant pressure along the parting line where flash begins. Two shapes are investigated, rectangular and ring slits that respectively correspond to modeling flash from straight and curved parting lines. Our equation for flash length, the distance to which the melt penetrates the gap developed between the parting surfaces, is our main result. Further, adimensionalizing not only unifies the results for straight and curved parting lines, but also provides insight into how rheology, pressure and geometry govern flash. Our approach avoids tedious numerical simulation and mold structural analysis. The theory is validated by our polycarbonate flash experiments.
Kyung Yl Kim, Hyung Su Kim, Jae Wook Lee, May 2006
Polymer-clay nanocomposites of various concentrations were prepared by ultrasonically assisted melt blend process. The ultrasonic blend process using high intensity ultrasonic wave was employed to enhance nano-scale dispersion during melt mixing of polymer blend and organically modified clay. The materials studied were linear polypropylene and polystyrene reinforced with organophilic montmorillonite clay (nanoclay) at 3-5 wt% loadings. The effectiveness of the proposed ultrasonic processing technique on polypropylene matrix nanocomposites was evaluated by XRD, rheological measurements and thermal properties. We expected enhanced breakup of layered silicate bundle and further reduction in the size of dispersed phase with better homogeneity compared to the different immiscible blend pairs.Also, it was expected that generation of macroradicals in polymer mixture can lead to in-situ copolymer formation by their mutual combination, which should be an efficient path to compatibilize immiscible polymer blends and stabilize their phase morphology in the absence of other chemical agents.
High density polyethylene (HDPE) /clay (Cloisite-20-A) nanocomposites were prepared by using single screw compounding extruder with continuous treatment of ultrasound at different amplitude up to 10?m. The die pressure and power consumption due to ultrasound were measured at different feed rates of materials of various clay concentrations up to 10 wt%. Rheological, mechanical and thermal properties of ultrasonically treated and untreated nanocomposites were studied. X-ray diffraction (XRD) and transmitted electron microscope (TEM) were used to investigate the dispersion of clay and nanocrostructure of composites. The experimental results showed that sonication enhanced the dispersion during melt mixing of HDPE and clay.
Abdelhadi Sahnoune, César García-Franco, Sudhin Datta, May 2006
We report on the thermal and the flow characteristics of newly developed propylene-ethylenediene terpolymers. These propylene-rich products were made using single site metallocene catalyst Exxpol™ technology and cover a broad range of chemical composition. The thermal transitions were determined using thermal scanning calorimetry (DSC). The glass transition temperature decreased from about -18 to -28 °C as the ethylene content was increased from 8 to 16 wt%. The crystallinity and the crystallization rate were also strongly affected by the composition. The linear viscoelastic behavior of the different polymers was measured with small amplitude oscillatory shear at various temperatures. The modulus and the viscosity are characteristic of linear polymers and are, for similar molecular weight, independent of chemical composition. The incorporation of un-saturation makes these polymers easily cross-linkable using various chemical or radiation techniques. The crosslinking helps extend their end-use application to elevated temperatures, much higher than their uncrosslinked copolymer counterparts, as demonstrated by dynamic mechanical thermal analysis measurements.
Michael W Boehm, Kurt Koelling, Chunmeng Lu, L. James Lee, May 2006
Recent advances have created a need to understand processing characteristics, e.g. shear effects and the velocity field, during micro/nano molding. Polymers can be used to study these characteristics in shear thinning and viscoelastic systems. Here, we present results for the processing of non-Newtonian polymeric fluids in micro/nano channels during multi-phase penetrating flow. The dynamics of bubble flow (e.g. bubble shape, amount of coating and the flow field in front of and around the advancing bubble) will be investigated in conjunction with the effects of non-Newtonian rheology on coating.
Jushik Yun, Darnell C. Worley II, Raman Patel, Keith Saunders, May 2006
Soft Thermoplastic Vulcanizates (soft-TPVs) have been developed for soft touch and elastic recovery applications. These low durometer, 15~30 Shore A materials were compared with soft non-crosslinked styrenic thermoplastic elastomers (TPEs). The mechanical properties, compression set, solvent resistance, rheological properties and dynamic mechanical properties were investigated. It was observed that these soft TPVs have excellent elastic recovery properties at 70°C and 100°C when compared to comparable TPEs. Specifically, long term compression set at 70°C for 1400 hours showed soft-TPVs to be 50% lower than that of similar TPEs. The tensile properties were lower for these soft-TPVs relative to the non-crosslinked TPEs. These “Soft Thermoplastic Vulcanizates” are ideal for applications in which lower compression set, higher elasticity and softness are required.
Chelsea Braybrook, Phil Bates, Marianna Kontopoulou, May 2006
A commercially available linear vibration welder has been modified to allow measurements of complex viscosity, storage and loss moduli of polymeric materials at frequencies relevant to those encountered in vibration welding. In order to make these measurements, a parallel plate fixture was constructed and mounted on a linear vibration welder. Piezoelectric shear force sensors and two accelerometers were used to accurately measure the forces and accelerations imposed on the polymeric materials. The device has been used to test two model viscoelastic materials.
Polypropylene (PP) was irradiated with an E Beam with doses of 2.5 Mega Rads (MR), 5 MR, 10 MR, 15 MR, and 20 MR. The un-irradiated and the irradiated material was analyzed using a parallel plate rheometer, capillary rheometer and gel permeation chromatograph (GPC). The objective of this effort was to probe the structural changes in the polymer using aforementioned analytical techniques and determine the utility of the E Beam technique for rheology control. Of interest was the ability to narrow the molecular weight distribution of the material to achieve better process-ability and repeatability. The scope is limited to the results from the previously mentioned analytical techniques. Behavior of the material in actual processes such as injection molding and extrusion is beyond the scope of this study.
Blends of Polymethyl Methacrylate and Polycarbonate (20/80 & 50/50) were made. This was accomplished using a Dual TekFlow Processor which has already demonstrated its ability not only to blend and intimately alloy polymers, but also offers the advantage to reduce the viscosity of the new blend by disentanglement. The result is usually a new blend, with properties closer to a theoretical mix, i.e. with a more predictable performance level than what has been possible by more conventional methods of blend preparation. Rheological and thermal testing shows that the blends have very little degradation and about 40% disentanglement, meaning an improved fluidity by 40% when compared to the compounded contribution of the individual components. The 20/80 PC/PMMA blends look white, extremely well dispersed, and could be mistaken, at first glance, with Polypropylene. Injection molded specimens were made for the blends and both virgin resins, which allowed for investigation of their comparative tensile, flexural, impact and thermal properties. Mechanical test results indicate that the properties of the 20/80 PC/PMMA blend are slightly better than the Virgin PMMA, whereas the 50/50 PC/PMMA blend has intermediary properties compared to both resins.
Biobased ‘green’ nanocomposites are the materials for the 21st century. Polyhydroxybutyrate (PHB) a bacterial bioplastic is recently highlighted because of its renewable resource based origin and its potential to replace/substitute petroleum derived non-biodegradable plastic like polypropylene (PP). The major drawback of PHB is its brittleness. This work investigates toughening mechanisms for PHB via incorporation of elastomeric components. Maleated polybutadiene with high grafting and low molecular weight was identified as the compatibilizer. The toughened PHB was characterized through their thermo-mechanical rheological and morphological analysis. The resulting toughened PHB showed ~440% improvement in impact strength over pure PHB with only 50% loss in modulus. The loss of modulus was recovered to permissible extent through incorporation of titanate modified montmorillonite clay. The hydrophilic clay was modified by titanate-based treatment to make it organophilic and compatible with the polymer matrix. The toughened PHB on reinforcement with 5 wt.% titanate based modified clay gave ~400% improvement in impact properties and 40% reduction in modulus over virgin PHB. The novel toughened bioplastic nanocomposites show potential as a green replacement/substitute of specific TPO for use in structural applications.
M. Hernández, M.N. Ichazo, C. Albano, J. González, May 2005
Rheological and mechanical behavior of EPDM rubber filled with woodflour was studied based on blend ratio and curing systems. Irradiation was also studied as an alternative crosslinking method. Results indicate that woodflour accelerates rubber vulcanization. When comparing curing systems, final overall vulcanizates properties did not deteriorate with the efficient system. Concerning irradiation, an optimum dose of 110 kGy was found, since lower doses do not promote crosslinking and higher doses tend to decrease overall properties.
Guangjian He, Jingping Qu, Xianwu Cao, Xiangfang Peng, May 2005
A novel dynamic capillary rheometer (DCR) was designed to investigate the viscoelastic characteristic of polypropylene melt. The pulsatile flow of polymer melt could be got by parallel superposition of oscillation on steady shear flow in this novel DCR. The vibration frequency-dependent behavior of the phase angle and the shear stress vs. shear rate loops can be determined during pulsatile extruding processing. With the increase of the vibration frequency, the elastic characteristic of PP melt becomes more apparent.
Ming Li, Ashwini Kumar, Jaydeep Kulkarni, May 2005
We present a cable extrusion study that involves flow around a deformable moving fiberglass strand inside a cable extrusion die. In addition to non-Newtonian rheology, the fluid-structure interaction (FSI) between the polymer melt and the moving strand is highly non-linear. Using computational fluid dynamics (CFD), we have gained insight of our extrusion process by studying the strand deflection, the strand speed and the strand tension. The numerical results showed value in guiding the extrusion process.
Khairul Alam, Costas Tzoganakis, John Perdikoulias, May 2005
A major challenge in profile extrusion die design is flow balancing at the die exit as an unbalanced flow causes distortion of the profile. This is especially true for complicated profile dies with uneven thicknesses in certain sections of the die. In this work, we demonstrate the use of a factorial statistical design of numerical experiments to study the effect of geometrical parameters and polymer shear thinning behavior on the optimum flow balancing of a profile die.
Jiri Vlcek, Walter Kopytko, Martin Zatloukal, Birane Touré, May 2005
This paper describes a case study dealing with the development of a three-layer product on a feedblock coextrusion system. The problems or phenomena that occurred during the product development experiments are explained via flow simulation and the rheological properties of the materials used. The results of the study are compared with real film samples produced during the development
A comparative rheological study of four pairs of isotactic and syndiotactic polypropylene resins with similar MFI was conducted. The rheological tests included double bore capillary rheometry, frequency sweeps and creep and recovery compliance. It was found that, for similar MFI, the viscoelastic behavior is significantly different between these two types of resins which suggest that stereoregularity has an important effect on the viscoelastic behavior of polypropylene melts.
This work studied the effect of three radiopaque fillers (barium sulphate, bismuth trioxide and tungsten metal) on the rheological, mechanical and thermal properties of a range of medical grade polyurethanes and polyvinylchlorides. The results showed significant changes in the melt viscosity, mechanical properties and phase transitions (Tg and log E’) with different filler type.
Kim McLoughlin Senior Research Engineer, Global Materials Science Braskem
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Kim drives technology programs at Braskem to develop advanced polyolefins with improved recyclability and sustainability. As Principal Investigator on a REMADE-funded collaboration, Kim leads a diverse industry-academic team that is developing a process to recycle elastomers as secondary feedstock. Kim has a PhD in Chemical Engineering from Cornell. She is an inventor on more than 25 patents and applications for novel polyolefin technologies. Kim is on the Board of Directors of SPE’s Thermoplastic Materials & Foams Division, where she has served as Education Chair and Councilor.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Gamini has a BS and PhD from Purdue University in Materials Engineering and Sustainability. He joined Penn State as a Post Doctorate Scholar in 2020 prior to his professorship appointment. He works closely with PA plastics manufacturers to implement sustainability programs in their plants.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Tom Giovannetti holds a Degree in Mechanical Engineering from The University of Tulsa and for the last 26 years has worked for Chevron Phillips Chemical Company. Tom started his plastics career by designing various injection molded products for the chemical industry including explosion proof plugs and receptacles, panel boards and detonation arrestors for 24 inch pipelines. Tom also holds a patent for design of a polyphenylene sulfide sleeve in a nylon coolant cross-over of an air intake manifold and is a Certified Plastic Technologist through the Society of Plastic Engineers. Tom serves on the Oklahoma Section Board as Councilor, is also the past president of the local Oklahoma SPE Section, and as well serves on the SPE Injection Molding Division board.
Joseph Lawrence, Ph.D. Senior Director and Research Professor University of Toledo
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Dr. Joseph Lawrence is a Research Professor and Senior Director of the Polymer Institute and the Center for Materials and Sensor Characterization at the University of Toledo. He is a Chemical Engineer by training and after working in the process industry, he has been engaged in polymers and composites research for 18+ years. In the Polymer Institute he leads research on renewably sourced polymers, plastics recycling, and additive manufacturing. He is also the lead investigator of the Polyesters and Barrier Materials Research Consortium funded by industry. Dr. Lawrence has advised 20 graduate students, mentored 8 staff scientists and several undergraduate students. He is a peer reviewer in several journals, has authored 30+ peer-reviewed publications and serves on the board of the Injection Molding Division of SPE.
Matt Hammernik Northeast Account Manager Hasco America
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Matt Hammernik serves as Hasco America’s Northeast Area Account Manager covering the states Michigan, Ohio, Indiana, and Kentucky. He started with Hasco America at the beginning of March 2022. Matt started in the Injection Mold Industry roughly 10 years ago as an estimator quoting injection mold base steel, components and machining. He advanced into outside sales and has been serving molders, mold builders and mold makers for about 7 years.
84 countries and 85.6k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Need help from SPE Headquarters?
SPE HQ provides a range of services to Chapters. If you are a chapter and need HQ services (i.e.,
event registration - full list of HQ services can be found here), please fill out and submit the HQ services request form found
here: www.4spe.org/HQservices.
IMPORTANT! If you are simply looking to post your
event on SPE's calendar, please click the "Submit an Event" button below. All events
submitted for inclusion in the SPE calendar are subject to approval.
Going to a SPE event?
If you are going to a SPE event and need a Visa invitation letter, please submit your request for a Visa Invitation letter.
SPE Members receive discounted rates on all event registrations. Not a member of SPE? Join today!
How to reference articles from the SPE Library:
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers, ISBN: 123-0-1234567-8-9, pp. 000-000.
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
