The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
Virgilio A. González, Moisés Hinojosa, Carlos Guerrero, Edgar Reyes, May 2000
The roughness of iso polypropylene films crystallized at different cooling rates was analyzed using atomic force microscopy. For this characterization it was used the methods of variable bandwith (ZMax) and box-counting in order to determinate the fractal or self-afine character of the surfaces and its roughness. The methods and its computational algorithms were evaluated with synthetic profiles obtained with the Weierstrass-Mandelbrot function. We report the observed deviations in roughens, the relationship between both methods and the effect of the cooling rate in the roughness of polypropylene films.
L. Morejón, E. Mendizábal, C.F. Jasso, J.A. Delgado, E.H. Barbosa, N. Davidenko, May 2000
Acrylic bone cements are widely used in orthopedic surgery to fix artificial prostheses in the body osseous structure. One of the most important applications in this area is in Total Hip Arthroplasty (THA). The cement has two main functions: to assure the short and long term anchorage of the implant to the bone, and to allow a better distribution of body loads between the prostheses and the bone (1-3). Nevertheless several adverse effects are associated with the use of bone cements in this field: high temperature of the polymerization reaction m ay cause thermal necrosis to the adjacent bone (4,5), the release of unreacted monomer, methylmethacrylate (MMA), produces chemical dam age in the surrounding tissues, and the shrinkage of the cement upon curing produces gaps in the bone/cement and cement/prostheses interfaces. Curing of the acrylic cement is a complex process and plays an important role in determining its performance and durability in the hum an body. In this work, the influence of hydroxyapatite types on the curing kinetics of acrylic bone cements is presented.
R.M. Corona, D. Likhatchev, O. Manero, S. Chvalun, A. Garciá-Rejón, May 2000
Polyethelene terephthalate (PET) is a polymer broadly used in food packing and containers for carbonated beverages. PET is attractive for its transparency, good mechanical properties and low permeability to O2 and CO2. However, an important disadvantage of the PET container is its low thermal resistance that does not allow hot-filling at sterilization temperatures such as 100°C. Polyethylene naphthalate (PEN) has been considered recently as the most promising alternative to PET. It possesses a glass transition temperature of 125°C which is 50°C higher to that of PET. This enables to fill containers made of this polymer at temperatures higher than 100°C. Another advantage of this polymer is its low permeability to O2 and CO2 which may be five times lower that that of PET. This increases the time of storage of the packed products.
The operating conditions of an atomic force microscope in contact mode (C-AFM) were determined for polymer surface analysis. Isotactic polypropylene (PP), polyethylene terephthalate (PET), and polystyrene (PS) film surfaces were analyzed. The most important restriction was to obtain sharp and clear 3-D images of the polymer microstructure without causing any harm to the specimens by the microscope tip. The obtained operating conditions were a force around 10-9 N and a scanning frequency range from 1.0 to 1.5Hz. These operating conditions are very far from the normal ones used for other rigid materials.
D. Likhatchev, S. Granados-Fócil, D. Guzmán-Lucero, B.L. Ruiz-Rojas, May 2000
Ortho substituted polypyromellitimides were prepared from ortho bis(amino)-phenols or tetraamines by means of either high temperature thermal treatment or low temperature catalytic imidization of poly(amic acid)s, PAAs. Cyclodehydration of the precursors, with ortho OH or NH2 groups in the diamine moieties, in the presence of aliphatic anhydrides and tertiary amines was accompanied by the formation of pendant acetate or acetamide groups, respectively. It was found that model compounds N-(2- hydroxyphenyl)- and N-(2-aminophenyl)- phthalamic acids cyclodehydrated spontaneously to form the corresponding imides at room temperature in aqueous media in the absence of any dehydration agent. A similar effect was observed for the o-hydroxy- and o-amino- polyimides. Treatment of N-(2-aminophenyl)-phthalamic acid with trifluoroacetic anhydride led to the isoimide with an ortho trifluoroacetamide group in the diamine moiety. This thermodynamically unstable compound easily underwent secondary cyclization to yield the ladder 1,2-benzoylenebenzimidazole structure. A higher yield was attained in this reaction when the number of atoms that form the heterocyclic rings was increased.
D. Likhatchev, G. Pulos, B. Ruiz-Rojas, J. Torres-Robles, O. Manero, May 2000
The monomer 4,4’-diaminotriphenylmethane (DA-TPM) was used for the first time in the synthesis of aromatic polyimides (PI-TPM) by Koton and coworkers in 1980.1 The polyimides, obtained from DA-TPM and 1,2,4,5-benzotetracarboxylic (PMDA) or oxydiphtalic (ODPA) dianhydrides by thermal ciclodehydration of the precursor polyamic acids (PAA), were very brittle and insoluble in any organic solvent. These disadvantages resulted in an underestimation of the DA-TPM as a monomer for more than fifteen years. A new attempt for the use of 4,4’-diaminotriphenylmethane for the synthesis of polyimides was undertaken in 1995.2 In that work, the polyamic acids based on DA-TPM and PMDA or 3,3’,4,4’-benzofenonetetracarboxylic dianhydride (BTDA) were converted to the final polyimides by catalytic ciclodehydration at room temperature in the presence of acetic anhydride and a tertiary amine. In contrast to the results of Koton et. al.,1 the polymers prepared by this technique showed a good solubility in amide solvents, pyridine and, at high temperatures, in phenolic solvents such as m-cresol, nitrobenzene, etc. Their films exhibit good mechanical properties including high elasticity.
Cesar G. Iñiguez, E. Michel, R. González-Nuñez, V.M. González-Romero, May 2000
The morphological stability of postconsumer PET/HDPE blends was studied. Blends at different composition of PET in HDPE, with and without compatibilizer (Kraton G-1652) were prepared in an internal mixer (HAAKE Rheomix 600) and in a twin screw extruder (LEISTRITZ). The mixtures from the extruder were obtained at different stretching ratios (VR/VE). From the morphological analysis of the blends, it is shown that when the copolymer is added to the mixtures, the particle size of the dispersed phase diminishes in some cases until 40% compared with un-compatibilized blends. Moreover, for the case of un-compatibilized blends, (previously prepared by extrusion), the particle size of the dispersed phase increases after being reprocessed in an internal mixer. This result is attributed to the coalescence phenomena that takes place during mixing process. In the case of compatibilized blend, the particle size and the average volume of the dispersed phase remain constant after to be re-processed. In this way, the compatibilizer reduces the interfacial mobility, the coalescence effects and stabilizes the morphology. Tensile mechanical properties confirm this result. Blends containing 10, 20, and 30 %vol. of PET in HDPE with Kraton indicate a strong influence of this copolymer on their properties.
Addition of vinyl silane grafted polypropylene to Sarlink® chemical foaming composition containing a water releasing compound was found to increase the extruder head pressure, foam diameter, and foam cell size in the extrusion foaming process. The resulting foams were found to have better compression set properties than the control samples containing no vinyl silane grafted polypropylene. The improvement in foamability was believed to be due to crosslinking and/or chain branching that took place involving vinyl silane groups in the polypropylene phase in the presence of water during the extrusion foaming process.
Reza Sadeghi, Edwin Willems, Ryszard Brzoskowski, May 2000
Addition of polyamide (PA) grafted compatibilizer to Polypropylene (PP) and ethylene-propylene terpolymer (EPDM) was found to increase the adhesion strength significantly in polyamide injection overmolding and coextrusion processes. Transmission Electron Microscopy studies show that after melt blending grafted-polyamide compatibilizer with thermoplastic vulcanizates (TPV), the polyamide is present as small distinctive particles in the PP matrix of the thermoplastic vulcanizate. During injection overmolding onto polyamide, a thin layer seems to be formed on the polyamide substrate and thermoplastic vulcanizate interface. Parameters like molecular weight of the grafted compatiblizer and compatibilizer content have been varied to optimize the adhesion strength of TPV to polyamide substrates.
A.H. Behravesh, H. Jaani, Majid M. Moghaddam, May 2000
Sandwich Panels have a wide field of use in applications such as construction of industrial and commercial buildings, insulation, etc. For large span sandwich panels, as used in housings, usage of thin and strong skins is a necessity. Among metals, an obvious candidate for skin is Aluminum (Al) because of its lightness. However, using plastics could further reduce a great deal of weight. A competitive candidate, in terms of strength, is Polycarbonate (PC), which is currently used in housing applications, in single or double sheets. Under a marketing motivation, an investigation was conducted to compare the properties of sandwich panels with polyurethane (PU) as a core material with two different skins; Al and PC. One of the primary aspects of the research was to theoretically asses thermal insulation performance of both panels with main emphasize on the solar radiation. The governing equations and boundary conditions were numerically solved. The results show that the skin absorptivity, core thickness, and core conductivity are the main parameters to control thermal insulating performance of a sandwich panel.
The properties of poly(ethylene terephthalate) (PET) and its copolymers containing 0.04~0.15 mol% pentaerythritol and trimethylolethane (TME) were investigated. The molecular weight of the copolymers increased with the comonomer content, and its effect was observed significantly in pentaerythritol copolymers, resulting in broad molecular weight distribution. The comonomer effect on the mechanical properties was not considerable. The shear viscosity of the copolymers showed the shear thinning at experimental shear rate range. The crystallization rate of the fiber containing 0.103 mol% pentaerythritol increased with the spin draw ratio and their birefringence was also increased, whereas decreased with the content of comonomer.
Seong Hun Kim, Dong Jun Kim, Hyun Nam Cho, May 2000
Mechanical and rheological properties of blends of a para hydroxy benzoate - ethylene terephthalate copolyester TLCP (PHB 80 / PET 20 mole%) with Poly(ethylene 2,6-naphthalate) (PEN) and Poly (ethylene terephthalate) (PET) were investigated. Torque values of blends with increasing PHB content abruptly decreased above 40 wt% of PHB content because the melt viscosity of ternary blends were decreased. Tensile strength and tensile modulus of blends containing above 30 wt% PHB were improved with increasing PHB content due to the formation of fibrous structure. The blend of 40 wt% PHB showed pseudo LC phase, and mechanical property was improved with thermal treatment. Rheological property changes with shear rate and processing temperature will be presented.
The robust design method aims to seeks to minimize the sensitivity of performance to uncontrolled variation. Product development frequently uses numerical simulations, analytic models and experimental data. However, these underlying predictions may be inaccurate, and include errors that causes the design to be unacceptable and require a design change. This paper presents a method that analyzes the possibility of a design change based on prediction uncertainty, and then estimates possible changes and evaluates the product design flexibility. The results indicate that small changes in design variables to increase robustness may reduce the likelihood and cost of future design changes.
In recent years designers of injection molded parts have widely adopted solid modeling techniques. The time to derive and prepare an analysis model has become burdensome. This is because conventional CAE analysis of injection molding has made extensive use of the Hele-Shaw approximation to simplify the equations governing the process. A consequence of this simplification is the need to generate a midplane mesh. This example of a technical limit hindering the use of a technology has changed with developments arising from Moldflow's product philosophy of Process Wide Plastics Simulation". PWPS has been enabled by three new technologies. In this paper we discuss these developments and how they will change the way analysis influences the design of injection molded plastic Parts"
The past five years have seen drastic improvements in injection molding simulation. While prior to this period, advanced simulations provided a wealth of information about a part and mold design, a common complaint was that too much time was required to perform an advanced simulation. This is part of the reason for the rise in popularity of desktop" simulations which provide fast useful results though not as detailed as advanced simulations. Besides improving part quality and reducing part costs one of the primary objectives of molding simulation use is to reduce the design cycle and the time to get a mold into production. This paper discusses recently developed molding simulation technology which greatly reduces the time requirement to run an advanced simulation and reduces the overall product development time."
Injection molders require a consistent optimization strategy for machine set-up and production control. The ultimate aim of an injection molding machine is to achieve 100% automatic inspection and quality control of all manufactured parts, where no unacceptable moldings are passed on to the customer. Process monitoring and control offers a key opportunity to the polymer processing industry enabling it to gain an understanding of its processes, to dispel its 'black art' image, and by this provide greater clarity for the machine operators and greater confidence for its expanding and highly competitive markets. The next major development for injection molding machine controllers is the integration of 'industry focussed' expert systems for process optimisation and production control. These expert systems will provide a well documented link between design and process engineering, passing information in both directions.
A comparative study of the melting and crystallization behavior is carried out between a metallocene type isotactic polypropylene and a narrow fraction of a Ziegler-Natta type with the same average defect content. At any crystallization temperature the melting temperature of the Ziegler fraction is ~ 3.5 °C higher than the metallocene. This difference is associated with the thicker lamellae thicknesses found in the fraction. The lamellae thicknesses were obtained by AFM, TEM and SAXS and good agreement was obtained between these techniques. The difference in thicknesses is interpreted as a consequence of a sustained heterogeneity of the intermolecular defect composition distribution in the Ziegler fraction even after fractionation. A second source for this difference could be a different partitioning of the defects present in the metallocene and in the fraction between the crystalline and the non crystalline phases. The product of the interfacial free energies obtained from nucleation theory, is very similar for both isotactic polypropylenes.
Érica Gervasoni Chaves, Maria de Fátima V. Marques, May 2000
Polypropylene with especial properties can be obtained by metallocenic catalysts, which represented the beginning of a new era in the polyolefins technology. In this context, some properties and principally some applications of sindyotatic polypropylene (s-PP) have not been well investigated. In this work, the influence of the metallocenic s-PP addition on the processability and on the mechanical properties of isotatic polypropylene (i-PP) was evaluated. It was observed that an increasing addition of s-PP promoted better processabilility, with an increasing in the impact strength. It was also verified a decreasing in the crystallinity of the blends, resulting in a decreasing in the stress at yield and module.
The interfacial tension between immiscible polymers is difficult to measure due to the high viscosity of molten polymers. Additionally, the lack of optical contrast that exists between two molten polyolefins renders conventional optical methods impractical. Small-amplitude oscillatory shear flow provides an indirect technique for measuring the interfacial stress between immiscible polyolefin binary blends. Based on the model of Palierne, the interfacial contribution to the measured rheological response is governed by the ratio of the interfacial tension to the average radius of the dispersed droplets. In this work we have investigated the use of amplitude oscillatory shear measurements to determine the interfacial tension in binary blends of immiscible polyolefins. The two-dimensional droplet morphology in each blend was characterized using tapping-phase AFM. True dispersion phase radii were obtained after converting the measured two-dimensional size distributions to three-dimensional size distributions through the linear transformation method of Schwartz-Saltykov. Results of measured interfacial tensions in various polyolefin blends are reported. The interfacial tension of a PP/EP blend thus obtained was in agreement with the value calculated from the SANS measurement.
A study to evaluate the rheological properties of organic in situ short polymer fibres (poly(butylene terephtalate) (PBT))/high density polyethylene (HDPE) and high density polyethylene/poly(ethylene-co-vinyl acetate) (HDPE/EVA9) composites has been carried out. The in situ compatibilization of the HDPE/EVA9/PBT systems with the Bu2SnO catalyst was performed. The different systems were melt blended in a twin screw extruder, drawn at the die exit and cooled. The results indicate that it is possible to produce such composites using reactive extrusion for compatibilization and post extrusion drawing to control the aspect ratio of the PBT fibres. Morphological analysis allowed evaluation of parameters such as draw ratio, PBT concentration and compatibilization on the size and shape of the fibrils. Their influence on the solid rheological behaviour is discussed.
Kim McLoughlin Senior Research Engineer, Global Materials Science Braskem
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Kim drives technology programs at Braskem to develop advanced polyolefins with improved recyclability and sustainability. As Principal Investigator on a REMADE-funded collaboration, Kim leads a diverse industry-academic team that is developing a process to recycle elastomers as secondary feedstock. Kim has a PhD in Chemical Engineering from Cornell. She is an inventor on more than 25 patents and applications for novel polyolefin technologies. Kim is on the Board of Directors of SPE’s Thermoplastic Materials & Foams Division, where she has served as Education Chair and Councilor.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Gamini has a BS and PhD from Purdue University in Materials Engineering and Sustainability. He joined Penn State as a Post Doctorate Scholar in 2020 prior to his professorship appointment. He works closely with PA plastics manufacturers to implement sustainability programs in their plants.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Tom Giovannetti holds a Degree in Mechanical Engineering from The University of Tulsa and for the last 26 years has worked for Chevron Phillips Chemical Company. Tom started his plastics career by designing various injection molded products for the chemical industry including explosion proof plugs and receptacles, panel boards and detonation arrestors for 24 inch pipelines. Tom also holds a patent for design of a polyphenylene sulfide sleeve in a nylon coolant cross-over of an air intake manifold and is a Certified Plastic Technologist through the Society of Plastic Engineers. Tom serves on the Oklahoma Section Board as Councilor, is also the past president of the local Oklahoma SPE Section, and as well serves on the SPE Injection Molding Division board.
Joseph Lawrence, Ph.D. Senior Director and Research Professor University of Toledo
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Dr. Joseph Lawrence is a Research Professor and Senior Director of the Polymer Institute and the Center for Materials and Sensor Characterization at the University of Toledo. He is a Chemical Engineer by training and after working in the process industry, he has been engaged in polymers and composites research for 18+ years. In the Polymer Institute he leads research on renewably sourced polymers, plastics recycling, and additive manufacturing. He is also the lead investigator of the Polyesters and Barrier Materials Research Consortium funded by industry. Dr. Lawrence has advised 20 graduate students, mentored 8 staff scientists and several undergraduate students. He is a peer reviewer in several journals, has authored 30+ peer-reviewed publications and serves on the board of the Injection Molding Division of SPE.
Matt Hammernik Northeast Account Manager Hasco America
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Matt Hammernik serves as Hasco America’s Northeast Area Account Manager covering the states Michigan, Ohio, Indiana, and Kentucky. He started with Hasco America at the beginning of March 2022. Matt started in the Injection Mold Industry roughly 10 years ago as an estimator quoting injection mold base steel, components and machining. He advanced into outside sales and has been serving molders, mold builders and mold makers for about 7 years.
84 countries and 85.6k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Need help from SPE Headquarters?
SPE HQ provides a range of services to Chapters. If you are a chapter and need HQ services (i.e.,
event registration - full list of HQ services can be found here), please fill out and submit the HQ services request form found
here: www.4spe.org/HQservices.
IMPORTANT! If you are simply looking to post your
event on SPE's calendar, please click the "Submit an Event" button below. All events
submitted for inclusion in the SPE calendar are subject to approval.
Going to a SPE event?
If you are going to a SPE event and need a Visa invitation letter, please submit your request for a Visa Invitation letter.
SPE Members receive discounted rates on all event registrations. Not a member of SPE? Join today!
How to reference articles from the SPE Library:
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers, ISBN: 123-0-1234567-8-9, pp. 000-000.
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
