The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
Guangyu Lu, Dilhan M. Kalyon, Iskender Yilgör, Emel Yilgör, May 2004
Extrudability of 20% (vol.) BaSO4 filled medical-grade (additive free) thermoplastic polyurethanes was investigated. Filled TPU exhibits decreased shear viscosity and elasticity in comparison to unfilled TPU, generating reduced pressure drop at the die and reduced pressurization in the extruder. The moisture remaining in the BaSO4 may hydrolyze the polymer. However, hydrolysis is not sufficient and air, entrained with the filler into the extruder, reduces the viscosity and elasticity of the compounded TPU.
The flow of a low-density polyethylene in a flat die is simulated using the axisymmetric and planar elongational viscosities estimated in an earlier publication by Beaupre and Gupta. Elongational viscosity is found to have only a limited effect on the velocity distribution at the die exit. However, the predicted pressure drop in the die and temperature distribution at the die exit changed significantly when the effect of elongational viscosity is included in the simulation.
A simulation-based approach is presented to optimally design polymer sheeting dies to operate over a range of operating conditions. The computational approach incorporates finite element simulations to quantify the ’goodness’ of a die design and includes a gradient-based optimization algorithm to update the die’s geometry. Examples are provided to illustrate the methodology for the creeping flow of purely viscous fluids through thin cavities that may be modeled with the Generalized Hele-Shaw approximation.
An overview and general description of the fundamental parameters that limit feed rates of twin screw extruders (TSE’s) and continuous mixers (CM’s) is presented. This paper also identifies relationships that can be used to identify the key rate limiting parameters for a given TSE/CM design and set of operating conditions.
Kinematic modeling has been shown to be important for the understanding and control of co-rotating twin screw extruders. Past techniques of kinetic modeling have dealt with the extruder as either one unit or a series of screw element wise units. In this work, multiple sensors are used to characterize the residence time distribution of an extruder. Additionally, the uncoupled signals from these sensors are deconvoluted to produce signals representative of the individual extruder zones.
The new extruder – project name S-Truder - surrounds the screw with a perforated sleeve to separate melt from unmelted resin. As soon as the melt develops, it flows through conically-shaped holes in the melting sleeve into the intermediate melting zone area and then with a pressure flow toward the screw tip. Therefore, the screw can then run at a higher rotation speed without overheating the polymer, and, in contrast to a “normal” screw, solid bed width is maintained. Experimental results and theoretical background will be described in this paper.
P.A. Brincat, A.S. Bakharev, R.G. Speight, May 2004
This document outlines the advantages of a closed-loop screw cushion control system for thermoplastic injection molding machines in the production environment. It also outlines the limitations of such a system and proposes a possible path forward towards closed-loop process control, through the use of a closed-loop viscosity control system.
Since variance in melt density during a molding process can infer a change of product quality, careful measurement – and subsequent management – of this factor is essential. Considering that temperature is the primary, though not only, factor in this process, injected melt temperature was measured through two means: a melt sensor installed into a machine nozzle, and a melt sensor installed into a heated insert assembly. The injected melt fill-and-pack density" was profiled for consecutive cycles and the resulting melt-flow profiles and sensing means are presented."
Uffe Rolf Arlø Theilade, Erik Kjær, Hans Nørgaard Hansen, May 2004
An experimental study of the effect of mold surface roughness on in-process in-flow linear part shrinkage in injection molding has been carried out. The investigation is based on an experimental two-cavity tool, where the cavities have different surface topographies, but are otherwise identical. The study has been carried out for typical commercial polystyrene and polypropylene grades.
Push-pull injection molding is a live in-mold manipulation method used for enhancing the orientation of molecules and fillers. It implements an alternating shear field induced by a coordinated action of two injection units to create multiple oriented layers across the thickness of moldings. In this work design of experiment was used to analyze the processing parameters in push-pull molding of polypropylene homopolymer. The microstructure and the flexural and impact properties of the produced parts were assessed.
Though molding for decades, we have yet to develop a scientific method of developing an optimized process. The established process is often poorly documented and cannot be transferred to another machine. This paper outlines a scientific process optimization based on data and defines the necessary variables to establish a reproducible consistent process. The procedure along with the resulting setup sheet, that will work on any appropriate machine (hydraulic or electric) are presented.
J.-W. John Cheng, Yu-Wei Lin, Fu-Sheng Liao, May 2004
Despite several researchers have reported excellent performance of iterative learning controls for injection molding process, a serious work remains, namely, stability guarantee of the learning controllers. This work presents the first effort on theoretical analysis of iterative learning injection molding control. Specifically, analysis of a filling velocity learning control is conducted. The analysis adopts Lyapunov’s indirect method. Experiment evaluation is carried out on a commercial injection molding machine.
David R Astbury, Alexander S. Bakharev, Russel Speight, May 2004
Modern systems for computer-assisted injection molding use data acquired from sensors and feedback from operators to setup the injection-molding process, to automate optimization of process parameters and to provide a statistical process control. A good initial starting point greatly streamlines injection molding setup and increases its robustness. Here we describe an algorithm for initial determination of injection velocity based on rheological calculations of the melt flow inside the mold cavity.
Micro features were produced on inserts for a macroscopic polymer injection mold. The inserts were produced using traditional machining and micro machining techniques. The inserts were installed and subsequent moldings were examined to measure the accuracy of replication of the micro features. The molding conditions were varied to identify the processing window available for accurate production of the micro features.
Injection over-molding involves injection of molten polymer into complex cavities over solid inserts to form fabricated parts. This process is non-isothermal and the flow is strongly affected by the presence of the insert, and its thermal and mechanical properties. This paper compares the three dimensional flow simulation results of metal and polymer inserts and reviews their effects on filling pattern with experimental data. Furthermore, a two shot over-molding simulation is also presented.
A new approach to runner balancing is proposed which identifies and deals with limitations associated with the traditional approach to runner balancing. The runner diameters are varied by a multi-objective genetic algorithm, which simultaneously optimizes the product shrinkage and cost. The results suggest that balanced runner systems, which exhibit large differences in cavity pressure, have lower product costs than systems characterized by similar fill times and cavity pressures. The optimization of the secondary runner lengths also reduced costs significantly.
Currently, CAE injection molding simulation software uses four major types of mesh for analysis. These four mesh types are beam (1D), mid-plane (2.5D), Dual Domain™ (modified 2.5D) and three dimensional (3D). Each mesh type is useful for simulating different types of plastic part geometries but also has its own limitations and assumptions. This paper will discuss the advantages and disadvantages of each mesh type through theoretical and experimental data.
The paper reviews the processing advantages and challenges of microcellular injection molding and summarizes the recent research results obtained at the University of Wisconsin-Madison. The study emphasizes on how the process conditions and micro-/nano-scaled fillers affect the microstructure and mechanical properties of microcellular injection molded components. In addition, initial results of a novel co-injection molding process that combines the aesthetic and processing advantages of injection molding with the property attributes and benefits of microcellular plastics (MCPs) are presented.
Sejin Han, R. Zheng, P. Kennedy, J. Xu, L. Kishbaugh, May 2004
This study presents a simulation model for the microcellular injection molding process in which supercritical fluid such as carbon dioxide or nitrogen is mixed with molten polymer and injected into the mold. Our model simulates the development of cells in the melt during injection molding. The effects of cell growth on material properties and flow have been investigated. Some simulation results such as melt pressure and final cell size distribution are compared with experimental results.
Overmolding is a non-conventional injection molding method in which two or more polymers are introduced sequentially with a time lag into a special mold. In this study experimental design was employed for investigating retractable insert overmolding of two PP/HDPE combinations. Optical microscopy was used for evaluating structure development. Mechanical properties were examined through flexural and impact tests. The role of the interface of the two materials on the overall mechanical behavior was analyzed.
Kim McLoughlin Senior Research Engineer, Global Materials Science Braskem
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Kim drives technology programs at Braskem to develop advanced polyolefins with improved recyclability and sustainability. As Principal Investigator on a REMADE-funded collaboration, Kim leads a diverse industry-academic team that is developing a process to recycle elastomers as secondary feedstock. Kim has a PhD in Chemical Engineering from Cornell. She is an inventor on more than 25 patents and applications for novel polyolefin technologies. Kim is on the Board of Directors of SPE’s Thermoplastic Materials & Foams Division, where she has served as Education Chair and Councilor.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Gamini has a BS and PhD from Purdue University in Materials Engineering and Sustainability. He joined Penn State as a Post Doctorate Scholar in 2020 prior to his professorship appointment. He works closely with PA plastics manufacturers to implement sustainability programs in their plants.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Tom Giovannetti holds a Degree in Mechanical Engineering from The University of Tulsa and for the last 26 years has worked for Chevron Phillips Chemical Company. Tom started his plastics career by designing various injection molded products for the chemical industry including explosion proof plugs and receptacles, panel boards and detonation arrestors for 24 inch pipelines. Tom also holds a patent for design of a polyphenylene sulfide sleeve in a nylon coolant cross-over of an air intake manifold and is a Certified Plastic Technologist through the Society of Plastic Engineers. Tom serves on the Oklahoma Section Board as Councilor, is also the past president of the local Oklahoma SPE Section, and as well serves on the SPE Injection Molding Division board.
Joseph Lawrence, Ph.D. Senior Director and Research Professor University of Toledo
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Dr. Joseph Lawrence is a Research Professor and Senior Director of the Polymer Institute and the Center for Materials and Sensor Characterization at the University of Toledo. He is a Chemical Engineer by training and after working in the process industry, he has been engaged in polymers and composites research for 18+ years. In the Polymer Institute he leads research on renewably sourced polymers, plastics recycling, and additive manufacturing. He is also the lead investigator of the Polyesters and Barrier Materials Research Consortium funded by industry. Dr. Lawrence has advised 20 graduate students, mentored 8 staff scientists and several undergraduate students. He is a peer reviewer in several journals, has authored 30+ peer-reviewed publications and serves on the board of the Injection Molding Division of SPE.
Matt Hammernik Northeast Account Manager Hasco America
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Matt Hammernik serves as Hasco America’s Northeast Area Account Manager covering the states Michigan, Ohio, Indiana, and Kentucky. He started with Hasco America at the beginning of March 2022. Matt started in the Injection Mold Industry roughly 10 years ago as an estimator quoting injection mold base steel, components and machining. He advanced into outside sales and has been serving molders, mold builders and mold makers for about 7 years.
84 countries and 85.6k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Need help from SPE Headquarters?
SPE HQ provides a range of services to Chapters. If you are a chapter and need HQ services (i.e.,
event registration - full list of HQ services can be found here), please fill out and submit the HQ services request form found
here: www.4spe.org/HQservices.
IMPORTANT! If you are simply looking to post your
event on SPE's calendar, please click the "Submit an Event" button below. All events
submitted for inclusion in the SPE calendar are subject to approval.
Going to a SPE event?
If you are going to a SPE event and need a Visa invitation letter, please submit your request for a Visa Invitation letter.
SPE Members receive discounted rates on all event registrations. Not a member of SPE? Join today!
How to reference articles from the SPE Library:
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers, ISBN: 123-0-1234567-8-9, pp. 000-000.
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
