The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
Kurt Feichtinger, Wenguang Ma, Tristan Touzot, September 2004
Recent advances in thermoplastic resin chemistry have enabled the development of a thermoplastic polyester foam core material with excellent thermoformability elevated temperature and chemical resistance and superior fatigue endurance. Possessing high strength and rigidity this foam product fulfills the demanding requirements for structural core materials used in sandwich composites though it can be successfully used without facings for many applications. Presented will be the physical properties including at elevated temperatures in comparison with rigid polyurethane foams and other core materials. The results of an extensive sandwich flexural fatigue study will also be reviewed and discussed. Finally examples of complex thermoformed shapes will be shown both of the foam alone and in combination with GMT facings to form contoured structural sandwiches all at once.
Hwan-Man Park, Manjusri Misra, Amar K. Mohanty, Lawrence T. Drzal, September 2004
Sustainable nanocomposites have been successfully fabricated from renewable cellulose acetate (CA) environmentally benign triethyl citrate (TEC) plasticizer and organically modified clay. The effects of processing conditions such as mixing methods pre-plasticizing times retention times (RT) and addition of compatibilizer maleic anhydride grafted cellulose acetate butyrate (CAB-g-MA) on the performance of these nanocomposites have been evaluated. The cellulosic plastic with CA/TEC (80/20 or 75/25 wt. %) was used as the polymer matrix for
nanocomposite fabrication. The morphologies of these nanocomposites were evaluated through X-ray diffraction (XRD) Atomic force microscope (AFM) and transmission electron microscopy (TEM) studies. From all the sequential mixing methods used powder-powder mixing leads to the most transparent nanocomposites. Cellulosic plastic-based nanocomposites obtained using increased pre-plasticizing times and RT showed better-exfoliated structures. Cellulosic plastic-based nanocomposites with 5 wt.% compatibilizer contents showed better-exfoliated structure than the counterpart having 0 or 7.5 wt.% compatibilizer contents. Polygonal shape of exfoliated clay platelets was observed with 500 nm width and 800 nm length by AFM and TEM imaging. The mechanical properties of the nanocomposites have been correlated with the XRD and TEM observations.
Bayer MaterialScience has focused on developing new composite technologies combining a lightweight low-density core together with fiber-reinforced polyurethane skins. A Bayer MaterialScience polyurethane chemistry designated Baypreg®F is ideally suited for constructing composites that require a high stiffness to weight ratio. The components of a composite made using these chemicals can be easily manipulated to allow part producers
extensive freedom in manufacturing a wide variety of part designs and configurations. This paper presents the development of a mathematical model for the prediction of composite properties. It specifically focuses on composites constructed with paper honeycomb as the core material and with glass fiber mat as the facing material. For typical composite applications load-deflection behavior is the most significant indicator of performance. Subsequently data accumulated from the testing of the core and facing materials individually is
used to predict the load-deflection behavior of a composite constructed utilizing the polyurethane chemistry. The theoretical predictions are compared directly to test data obtained from composites with specific constructions. A discussion of the model’s predictive ability focusing on part design to meet customer
requirements quickly and efficiently will be presented. Work targeted towards refining the model will serve as a conclusion to the discussion.
New automotive applications of sandwich composites require the development and characterization of reliable attachment techniques needed for the creation of functional structures. Baypreg®F is Bayer’s proprietary name for the two-component polyurethane material that bonds and holds the composite structure together which is normally made of a honeycomb-type paper core sandwiched between glass fiber mats. In this paper we present testing results to compare different attachment strategies applicable to this type of sandwich composites. As joints are a potential source of stress concentration and weight increase their performance should be as good as if not better than the underlying composite. We compare the performance of adhesive bonds embedded inserts and mechanical fasteners and discuss their advantages and disadvantages. Furthermore we discuss characterization of attachment techniques for computer simulations and outline plans for further development and testing.
Lynn Klett, Barbara Frame, Vlastimil Kunc, September 2004
In May 2003 Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) began collaboration on a four year research effort focused on developing technically robust and economically attractive joining techniques to overcome the technical issues associated with joining lightweight materials in heavy vehicles. This work is being performed concurrently with an industry program led by Delphi to develop and commercialize composite chassis components which is a “focal project” that will utilize the improved joining
methods. The initial joint design for a composite component to steel member will likely include mechanical fasteners requiring holes in the composite member. Several hole fabrication methods have been evaluated including drilling with tapered and Forstner bits laser cutting water jet cutting and punching. Several methods have been used to determine the damage associated with hole fabrication. One non-destructive method flash thermography has good correlation with x-ray dye penetrant results and in some cases shows finer detail and can indicate the location of damage through the thickness of the composite. A testing methodology has been developed to study the effects of bolt torque level on a pultruded fiberglass composite material. Informati
on derived from this will ultimately support the characterization of bolted composite assemblies and provide insight for the design and manufacture of the composite chassis components. Loss of pre-load data can be used to
predict the creep response in the through-the-thickness direction of the composite materials.
Xin Sun, Elizabeth Stephens, Darrell Herling, September 2004
This paper summarizes the Pacific Northwest National Laboratory (PNNL’s) progress-to-date on the development of joint designs for a composite structural member attached to a metal member for heavy vehicle chassis components. The joint design baseline was first established by characterizing the static and fatigue strength of a steel/steel Huck bolt joint assembly. The effects of various manufacturing factors and operational conditions on the static and fatigue strength of the hybrid joint were studied with a commercially available composite material. It was found that loading mode and washer size have significant influence on the static and fatigue strength of the hybrid joint. In addition it was found that a test frequency of 15 Hz can be used for the hybrid joints without inducing significant temperature changes during fatigue testing.
Peter H. Foss, Charles C. Mentzer, Douglas W. Franklin, September 2004
A thermoplastic composite version of a typical SUV liftgate was designed and built to investigate mass reduction over the production steel design. This paper documents the comparison of experimental stiffness of the liftgat
e with predictions using several finite element models of increasing detail. One of the most time consuming aspects of modeling the stiffness of composite structures is modeling panels stiffened with ribs. Creating and meshing each individual rib represents a significant time investment. By using isogrid ribbed panels to evaluate the structural stiffness of panels stiffened in specific areas many different rib heights thicknesses spacing etc. can be modeled in a very short time. However care must be taken that the isogrid ribbed areas are feasible within geometric constraints imposed on the future detailed design. We will show that when properly applied the concept of modeling ribbed areas of panels with the isogrid simplification gives excellent accuracy.
Highly filled thermoset compression-molded fuel cell stack plates are key elements in the design of a high-performance low-cost fuel cell stack. Much analysis research and testing have been performed to meet performance and manufacturability criteria for these plates which contain complex geometry and must meet exacting tolerances in some areas. A current deficiency in the development process is the inability to predict
mold filling for the stack plates in a process with highly filled thermoset composites and compression molding. Mold-filling analysis can be used to optimize plate design mold design and the manufacturing process thereby saving time and improving quality. This paper will discuss a strategy to develop mold-filling analysis with the goal of cultivating a predictive tool for use in the manufacture of fuel cell stack plates and highly filled thermoset composites. A series of molding trials was performed and the results were used to calibrate a model resulting in a model that correlated well to the real-world case.
The marine aircraft and heavy truck transport industries have long used structural and semi-structural sandwich panels for their excellent performance/weight ratio. More recently the automotive industry has also discovered the advantages of lightweight sandwich constructions mainly for interior applications such as load floors and rear parcel shelves. However for high-volume applications there are the additional demands of low cost and for European markets in particular full recyclability. A new sandwich construction based on a 100% PP solution could be the answer. A combination of an extruded PP hollow structure covered in-line with a self-reinforced PP skin
offers light weight good mechanical performance resistance to moisture and chemicals good thermoformability full recyclability using existing channels and a good cost/performance ratio.
Rich Simmons, John Stoll, Lloyd Hilligoss, September 2004
This paper offers a glimpse at emerging technology related to the application of composites in automotive structures. In a practical embodiment of this technology composites comprised of thermoplastic polymers and fiberglass are married with a structural core and garnished with a decorative carpet to form an automotive load floor. The exclusive polymer used throughout this particular load floor is polypropylene. Thus the composite structure is comprised entirely of polypropylene and fiberglass. Among the major advantages of this design are the following characteristics: structural integrity low weight excellent thermal stability acoustic abatement incorporation of recycled raw materials and the opportunity for end-of-life component recycling. Regarding processing of this load floor additional key advantages exist such as: low cycle time good formability one-step part consolidation high automation and the low environmental impact associated with thermoplastic polymers. Conceptually products of this type promise to have a lasting impact on the environment through all phases of product life cycle. This is achieved at first by utilizing recycled raw materials going into the product. Next offal from processing is recycled back into the materials stream. In addition the system creates a product of a known common composition of materials which possesses a higher potential for recycling as a whole after the useful life of the vehicle.
Eric Kleven, Dan Houston, J.T. Lyons, September 2004
The presentation will review the engineering considerations that led the Ford GT team to the development of the industry-first one-piece carbon fiber inner panel for the rear deck enginer cover and the associated manufacturing process. While most of the structural components of the 2004 Ford GT are aluminum the size of complexity of the rear deck drove the team to use carbon fiber for the inner structure. Instead of using multiple stamped aluminum pieces to make the inner structure the team decided to use carbon fiber composite technology to reduce weight control dimencional accuracy and for the total program cost benefit. The paper will also discuss the manufacturing of the component by Sparta Composties Inc (Sand Diego CA). The deck inner is made by hand lay-up of unidirectional carbon fiber/epoxy prepreg on an Invar mold for autoclave cure. In order to achieve the full-production rate of this complex panel a number of techniques are employed including a laser placement system which simplifies lay-up operations.
Marcia Kurcz, Burak Baser, Harri Dittmar, Joachim Sengbusch, Hans Pfister, September 2004
This paper will discuss the use of glass-mat-ther
moplastic (GMT) composite to replace steel
in spare-wheel wells (SWW) by European automakers and tier suppliers. Although this
application has been successfully translated across multiple OEMs and platforms in this
geography for 10 years it is still little known and less understood in the Americas and
Asia/Pacific despite its numerous advantages. In an attempt to help automakers and tier
suppliers in other parts of the world understand the benefits of this technology the paper will
discuss OEM performance criteria design requirements tooling and manufacturing of the part
as well as requirements for finished assembly in
to the vehicle vs. traditional steel systems.
As weight reduction is required for ecological aspects and in certain areas of the vehicle for dynamic handling requirements and besides this metallic materials cannot be extensively substituted within the short-term structurally bonding metallic materials with CFRP is necessary. Cathodic dip painting (CDP) which precedes the bonding process is able to offer good protection in order to combat sub-surface corrosion (bondline corrosion) which is also familiar from bonded metal joints. If the CFRP structural part has to be painted together with the
entire body-in-white the CFRP component and therefore the joining process may be integrated into the production sequence directly downstream of CDP. If joint painting is not necessary the joining process may be carried out at the beginning of assembly directly following paint drying. High thermomechanical stress in the production process can therefore be avoided and the problem is reduced to the vehicle's operating temperature range. The paper shows the characteristic properties of different adhesive systems e.g. two-component epoxy polyurethane or methacrylate in bonded CFRP-metal joints based on quasi-static test results. Especially the requirements on withstanding thermomechanical stresses in production and vehicle's operating temperature range are shown and evaluated by tests at different temperatures. The results shown in this article are developed in a cooperation project of Volkswagen AG Wolfsburg LWF Transfer GmbH & Co. KG and LWF Paderborn University Germany.
Michael Shoemaker, Dave Bank, Peter Cate, September 2004
Cyclic oligomers of butylene terephthalate (CBT®) represent a new chemical route to semi-crystalline thermoplastic polybutylene terephthalate (PBT). The oligomers of interest melt completely at about 150°C to produce a low-viscosity fluid that is ideal for wetting and dispersing fibrous fillers and reinforcements thereby enabling the development of composites that were previously not possible when working with high-viscosity commercial PBT. Introduction of catalyst to undiluted molten cyclic oligomer leads to rapid ring opening polymerization and the formation of high-molecular-weight thermoplastic PBT without the generation of volatile organic compounds. The polymer resulting from this polymerization will be hereafter referred to as pCBT. Treatment of cyclic oligomers in this fashion results in pCBT thermoplastic resin with a high melting point (230°C) and physical performance similar to that of other commercially available PBT resins. The low viscosity of these oligomers enables the selection of processing technologies that are typically reserved for thermosetting systems and that work in conjunction with easy flowing monomers or pre-polymers. The combination of excellent mechanical performance and the ability to utilize processing techniques typically reserved for thermosets enables broad uses for these oligomers in a range of applications including interior exterior and structural automotive components. Additionally the thermoplastic nature of pCBT holds promise to provide a low-capital route to a new family of pCBT-based recyclable materials made using a range of plastic processing technologies.
Glass-mat reinforced thermoplastic (GMT) composites have increasingly begun to replace traditional sheet molding compounds in automotive applications owing to their reduced weight. Both processing and end use put special demands on the stabilizer package incorporated in the poly(propylene) resin phase of the GMT composite. A novel ternary antioxidant blend based upon an aromatic amine type stabilizer for superior processing stabilization in GMT will be presented. Processing stabilizer performance data as measured by the critical weight loss test at 230 °C will be discussed. Comparison of the arylamine based blend which is phosphite-free with a traditional phosphite-containing package of otherwise similar composition confirmed the superior performance of the former.
Merry Lo, Suhara Panthapulakkal, Mohini Sain, September 2004
This research work aims to replace glass fibres in sheet molding compounds (SMC) by renewable natural fibres. These eco-efficient and cost effective SMC with natural fibres are gaining much attention in the automotive industry because of their specific properties. The specific objective of the work was to develop a high performance natural fibre hybrid SMC to meet the specifications required for automotive parts such as front fenders body panels etc. Hemp fibres with and without a combination of a small amount of glass fibres were used to reinforce vinyl ester resin for making SMC. Different combinations of layers of hemp and glass fibres were made to prepare SMC. Mechanical properties such as tensile and flexural properties and impact strength of the SMC prepared were found to be highly promising. The current OEM specifications for automotive parts for example rare lift gate and front fenders recommend the composite should have tensile strength of 62 MPa and tensile modulus of 2 GPa (Source of Automotive Engineers Car Technology yearbook 2000” USA 2000 Body panels Properties). SMC prepared by the combination of 45% of hemp fibres and 5% of glass fibres showed tensile strength and modulus were more or less same or better than that of the requirements for car body parts such as rare lift gate and front fenders (Tensile strength greater than 62 MPa and tensile modulus of 2 GPa).Use of this SMC with natural fibre is an economically viable alternative to SMC with glass fibres and at the same time it helps
reducing the green house gas emission as there is lesser amount of synthetic resins and plastics.
Sheet molding compound (SMC) is widely used in automotive parts appliances furniture and construction. These materials heavily depend on the petroleum supply which is depleting fast. The use of plant oils as an alternative source for SMC resins presents economic and environmental advantages over petroleum. Two synthetic methods have been used to develop new resins from triglycerides. The double bonds presented on the fatty acid chains were first converted to epoxy or hydroxyl functionality; the hydroxyl groups were maleinized while the epoxies were acrylated and then further maleinized. When these functionalized oils were combined with 33.3 wt% styrene the polymers showed mechanical properties comparable to those of commercial unsaturated polyesters. In addition these new resins exhibit adequate thermo-reversible thickening behavior with MgO. These triglyceride-based resins have good compatibility with natural fibers such as hemp and flax to form low-cost green composites. New bio-based nanocomposites were also developed using these new resins and organo-treated clays and the nanocomposites showed considerable increase in modulus and toughness. These new green materials show the promise to be used in the automotive industry.
In the past few years natural fibers are finding an increased interest in polymer matrices.
The natural fibers serve as reinforcement by enhancing the strength and stiffness to the resulting composite structure. In this study a novel processing technique has been developed for water based thermoset polymers to prepare resin-impregnated mats which can be used for sheet molding process to manufacture complex automotive semi-structural and structural parts. In order to optimize the curing conditions the mechanical properties of composites at different curing temperature and the crosslink density of the composites cured at different times were evaluated. The optimum curing cycle was obtained at 180 ºC for 10 min. Composites with one and two layers of impregnated mat with 40 % resin and 60 % fiber were manufactured and their performance were evaluated. The mechanical properties of the cured pure resin and hemp fiber acrylic based composites with two different fiber lengths were measured and the effect of fiber content and fiber length were investigated. The flexural strength was found to be around 94 MPa and the flexural modulus was 14 GPa for the composite.
C.C. Eberle, C.J. Janke, C.S. Wang, September 2004
Continuous carbon fiber/epoxy automobile hoods were electron beam cured to demonstrate
the capability to achieve curing throughput rates needed on automotive production lines. The
project team demonstrated curing speed of 180 hoods/day. This demonstration extrapolates to
1600 hoods/day curing throughput using a more powerful electron accelerator and much
higher throughputs may be achievable with innovative design and materials development.
Single-pass curing was shown to be feasible. The curing costs are potentially attractive
especially at high production volumes
Test laminate properties considerably exceeded those of the finished hoods. Hood thermo-
mechanical properties and surface finish need improvement. This is not surprising since this
was the team’s first attempt to manufacture electron beam cured automobile structures. Several
technical barriers were identified that need further attention.
Equal channel angular extrusion creates novel properties in metal and polymer materials.
Recently the authors investigated the effects of this process on commercial short fiber
composites. Experiments show that ECAE provides a means for controlling fiber length and
orientation in the extrudate. The process might transform continuous fiber thermoplastic matrix
composite sheets into high volume fraction discontinuous fiber sheet for thermoforming. In
addition the process might provide a method of recycling reground components into high-value
sheets with a known fiber orientation.
Kim McLoughlin Senior Research Engineer, Global Materials Science Braskem
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Kim drives technology programs at Braskem to develop advanced polyolefins with improved recyclability and sustainability. As Principal Investigator on a REMADE-funded collaboration, Kim leads a diverse industry-academic team that is developing a process to recycle elastomers as secondary feedstock. Kim has a PhD in Chemical Engineering from Cornell. She is an inventor on more than 25 patents and applications for novel polyolefin technologies. Kim is on the Board of Directors of SPE’s Thermoplastic Materials & Foams Division, where she has served as Education Chair and Councilor.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Gamini has a BS and PhD from Purdue University in Materials Engineering and Sustainability. He joined Penn State as a Post Doctorate Scholar in 2020 prior to his professorship appointment. He works closely with PA plastics manufacturers to implement sustainability programs in their plants.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Tom Giovannetti holds a Degree in Mechanical Engineering from The University of Tulsa and for the last 26 years has worked for Chevron Phillips Chemical Company. Tom started his plastics career by designing various injection molded products for the chemical industry including explosion proof plugs and receptacles, panel boards and detonation arrestors for 24 inch pipelines. Tom also holds a patent for design of a polyphenylene sulfide sleeve in a nylon coolant cross-over of an air intake manifold and is a Certified Plastic Technologist through the Society of Plastic Engineers. Tom serves on the Oklahoma Section Board as Councilor, is also the past president of the local Oklahoma SPE Section, and as well serves on the SPE Injection Molding Division board.
Joseph Lawrence, Ph.D. Senior Director and Research Professor University of Toledo
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Dr. Joseph Lawrence is a Research Professor and Senior Director of the Polymer Institute and the Center for Materials and Sensor Characterization at the University of Toledo. He is a Chemical Engineer by training and after working in the process industry, he has been engaged in polymers and composites research for 18+ years. In the Polymer Institute he leads research on renewably sourced polymers, plastics recycling, and additive manufacturing. He is also the lead investigator of the Polyesters and Barrier Materials Research Consortium funded by industry. Dr. Lawrence has advised 20 graduate students, mentored 8 staff scientists and several undergraduate students. He is a peer reviewer in several journals, has authored 30+ peer-reviewed publications and serves on the board of the Injection Molding Division of SPE.
Matt Hammernik Northeast Account Manager Hasco America
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Matt Hammernik serves as Hasco America’s Northeast Area Account Manager covering the states Michigan, Ohio, Indiana, and Kentucky. He started with Hasco America at the beginning of March 2022. Matt started in the Injection Mold Industry roughly 10 years ago as an estimator quoting injection mold base steel, components and machining. He advanced into outside sales and has been serving molders, mold builders and mold makers for about 7 years.
84 countries and 85.6k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Need help from SPE Headquarters?
SPE HQ provides a range of services to Chapters. If you are a chapter and need HQ services (i.e.,
event registration - full list of HQ services can be found here), please fill out and submit the HQ services request form found
here: www.4spe.org/HQservices.
IMPORTANT! If you are simply looking to post your
event on SPE's calendar, please click the "Submit an Event" button below. All events
submitted for inclusion in the SPE calendar are subject to approval.
Going to a SPE event?
If you are going to a SPE event and need a Visa invitation letter, please submit your request for a Visa Invitation letter.
SPE Members receive discounted rates on all event registrations. Not a member of SPE? Join today!
How to reference articles from the SPE Library:
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers, ISBN: 123-0-1234567-8-9, pp. 000-000.
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
