The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
An experiment was conducted to measure the energy
consumed during extruder runs with two different
polymers (one crystalline and one amorphous), each
utilizing three different screw designs. Energy
contributions from the individual heating zones on the
extruder were measured and analyzed. Also, the energy
consumed by the motor was measured to provide
comparison of the contributions from the heaters and the
motor. Results show value both in analyzing material
behavior and in evaluating screw performance from an
economic and a productivity standpoint.
Kevin Menard , Andrew Salamon , Witold Brostow , Noah Menard , W. Chonkaew , Carmem Pffiefer , Sherman Newman, May 2010
The application of DSC and DMA to photo-initiated
reactions specifically curing and degradations are
discussed. The influence of the light source its duration
and intensity are investigated in regards to the final
properties of the material. The use of Hyper DSC
techniques as well as simultaneous DMA-NIR in the study
of optically cured materials is discussed.
Kevin Menard , Andrew Salamon , Witold Brostow , Noah Menard , W. Chonkaew , Carmem Pffiefer , Sherman Newman, May 2010
The application of DSC and DMA to photo-initiated reactions, specifically curing and degradations, are discussed. The influence of the light source, its duration and intensity are investigated in regards to the final properties of the material. The use of Hyper DSC techniques as well as simultaneous DMA-NIR in the study of optically cured materials is discussed.
Sandeep Manandhar , Nandika D’Souza , Philippe Zimmern, May 2010
The importance of electrospun fibers as tissue
scaffolds has been an area of significant growth. In this
work, we will utilize electrospinning in conjunction with a
biodegradable polymer, Polycaprolactone (PCL) to make
thin fibers. These PCL fibers can be made into a mesh for
tissue scaffolds. Electrospinning utilizes electrostatic
force to draw fibers from solution.
Ken Miyata, Yuuki Ichikawa, Keiji Katsuno, Akihiro Nishioka, Tomonori Koda, Go Murasawa, May 2010
Tyco Electronics has over fifty years of experience in the field of radiation crosslinked polymers. We have incorporated the use of rheological and solvent swelling techniques to characterize crosslinked networks. Insufficient beam dose or processing errors can result in materials that appear crosslinked upon initial testing, but are not fully crosslinked. We evaluated various characterization methods on three different morphologies of polyethylene (HDPE, LDPE and VLDPE). Each method had its own strengths and limitations.
The present study was devoted to the effect of
nanoparticle on melt strength of blends. And the
reinforcing mechanism of PP/PA6/organoclay
nanocomposites had been investigated by DSC and SEM
analysis. The results showed that the maximal melt
strength existed and appeared as the weight ratio of
organoclay was 2 wt%. In addition blends presented the
best integrated properties at this ratio.
The present study was devoted to the effect of nanoparticle on melt strength of blends. And the reinforcing mechanism of PP/PA6/organoclay nanocomposites had been investigated by DSC and SEM analysis. The results showed that the maximal melt strength existed and appeared as the weight ratio of organoclay was 2 wt%. In addition, blends presented the best integrated properties at this ratio.
Kun Chang Lin , Chia-Hsun Chen , Chen-Feng Kuan , Hsu-Chiang Kuan , Sin-Jhih Peng, May 2010
Underwater pelletizing currently is the most promising, most innovative and, concerning the range of plastics materials to be processed, the most flexible technique for the production of high-quality plastics pellets.In this work, we established the experimental analysis of the underwater pelletizing system for producing pellets. The key process conditions for producing small pellets (<1.5mm) are low extrusion throughput, high cutter rotating speed, and low possibility of die freeze-off.
Nan Chen, Mohammad Monirul Hasan, Takashi Kuboki, Chul B. Park, May 2010
Polyamide 6 (PA6)/Clay 30B nanocomposites of various concentrations were prepared at different amplitudes using an ultrasonic extruder. The die pressure and ultrasonic power consumption were measured. X-ray patterns, thermal, mechanical and rheological properties of extruded nanocomposites were obtained. Films were manufactured from prepared nanocomposites by film blowing process and their structural and mechanical properties in the machine and transverse directions were studied.
Sarah Chung , Tieqi Li , Ken Oliphant , Patrick Vibien, May 2010
There have been several studies on the impact of chlorine on plastic piping systems in potable water applications and methodologies of ensuring performance have been successfully developed. The impact of chlorine dioxide is less well known. In this paper laboratory exposed plastic pipe samples are examined to study the impact of chlorine dioxide on oxidative degradation in potable water applications. The mechanisms of oxidation are characterized and recommendations for long-term performance validation are presented.
H. C. Chen, S. C. Chen, P.M. Hsu, H. S. Peng, Y. C. Wang, May 2010
LLDPE/Clay 20A nanocomposites of various concentrations were prepared at different amplitudes using an ultrasonic extruder. The die pressure and ultrasonic power consumption were measured. X-ray patterns, thermal, mechanical and rheological properties of extruded nanocomposites were measured. Films were manufactured from prepared nanocomposites by film blowing process and their structural and mechanical properties in the machine and transverse directions were studied.
In this research proteins were micropatterned on poly (lactic acid) (PLA) films. Poly(acrylic acid) (PAA) was micropatterned using photolithograph. These micropatterns were characterized using ATR-FTIR spectroscopy and toluidine blue dye staining. Acid groups were subsequently conjugated with amine terminated biotin using carbodiimide chemistry. Biotin micropatterned PLA films were then immersed in a solution of fluorescenceconjugated streptavidin. The streptavidin adsorption behavior was examined by fluorescence microscopy.
H. Inoya, Y. W. Leong, S. Thumsorn, S. Thitithanasarn, H. Hamada, May 2010
Viscoelastic secondary flows occurring in square ducts are simulated using the open source finite volume-based software, OpenFOAM. To validate a viscoelastic solver, experimental observations by other researchers were successfully reproduced, as well as compared to finite element results and recent results of a meshless technique known as the Radial Function Method (RFM). A single mode Giesekus and a multi-mode Phan-Thien Tanner (PTT) model are implemented to reproduce full three-dimensional (3D) flow through a square duct.
Dana Hnidáková , Roman Cermák , Jana Výchopnová, May 2010
The paper focuses on the role of ethylene-propylenediene rubber compatibilizer in the formation of polypropylene microfibrils in polyethylene matrix during extrusion through semihyperbolic die. Several blends varying in phase composition was processed. The structure and properties were examined by scanning electron microscopy DSC and tensile testing. Significant changes in morphology and properties were observed.
Shia-Chung Chen, Pham Son Minh, I-Sheng Hsieh, Yan-Chen Chiou, May 2010
Polystyrene (PS) foams have a number of desirable properties and thereby have been used for many applications. However, one of the most notable drawbacks of PS foams is its non-biodegradability. In recent years, polylactide (PLA) has been viewed as an environmentally sustainable substitute of PS. In this context, this paper aims to provide head-to-head comparisons between PLA and PS foaming processes, in terms of the cell formation mechanisms and foamability of the resultant foams.
In this paper the effects of ionizing radiation on poly(lactic acid) PLA will be investigated. The PLA used in this experiment is a NatureWorks LLC extrusion and thermoforming polylactide resin product code 2002D. Its rheological properties will be investigated. This team worked in conjunction with Mr. Song Cheng and Scott Goetz of Sterigenics and Professor John Bartolomucci of the Pennsylvania College of Technology. The material was irradiated using electron beam radiation. The material was then tested to obtain rheological properties at various dosage levels.
Han-Xiong Huang, Jian-Kang Wang, Hong-Fei Xu, May 2010
In this work, symmetric and asymmetric structural polyethylene foams were produced via compression molding using a chemical blowing agent and wood fibres as reinforcement. By modifying the temperature field in a compression molding process, it is possible to adjust the density across the partƒ??s thickness. Here, the results are discussed in terms of density profile and mechanical properties.
José M. Hernández , Ma’moun Abu-Ayyad , Rickey Dubay, May 2010
Many investigations have emphasized the importance of cavity pressure in determining final part quality in an injection molding machine. During the injection cycle the main factor affecting cavity pressure is the screw hydraulic pressure valve Y3. Cavity pressure has some nonlinear characteristics thus an advanced control strategy is developed. Experiments quantified the relationship between the nozzle pressure and the Y3 valve in order to design a predictive controller. The controller was implemented with good closed loop results.
Lenka Chvátalová, Jana Výchopnová, Roman Cermá, Martin Obadal, May 2010
The fountain flow effect affects the orientation of the macromolecules and the mechanical and optical properties of injection molded parts. The fountain flow effect is modeled using the Radial Functions Method (RFM). In this paper, the flow in a planar slit and a steady state is considered. Good agreement between the obtained results (velocity field, pressure field and front shape) and the existing data in the literature was attained.
An investigation into the effect of injection pressure screw position barrel temperatures and other variables on cavity pressure data is presented. This approach consists of monitoring key process data features and using a Projections to Latent Structures (PLS) multivariate modeling technique to correlate injection molding process variables to cavity pressure data.
Kim McLoughlin Senior Research Engineer, Global Materials Science Braskem
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Kim drives technology programs at Braskem to develop advanced polyolefins with improved recyclability and sustainability. As Principal Investigator on a REMADE-funded collaboration, Kim leads a diverse industry-academic team that is developing a process to recycle elastomers as secondary feedstock. Kim has a PhD in Chemical Engineering from Cornell. She is an inventor on more than 25 patents and applications for novel polyolefin technologies. Kim is on the Board of Directors of SPE’s Thermoplastic Materials & Foams Division, where she has served as Education Chair and Councilor.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Gamini has a BS and PhD from Purdue University in Materials Engineering and Sustainability. He joined Penn State as a Post Doctorate Scholar in 2020 prior to his professorship appointment. He works closely with PA plastics manufacturers to implement sustainability programs in their plants.
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Tom Giovannetti holds a Degree in Mechanical Engineering from The University of Tulsa and for the last 26 years has worked for Chevron Phillips Chemical Company. Tom started his plastics career by designing various injection molded products for the chemical industry including explosion proof plugs and receptacles, panel boards and detonation arrestors for 24 inch pipelines. Tom also holds a patent for design of a polyphenylene sulfide sleeve in a nylon coolant cross-over of an air intake manifold and is a Certified Plastic Technologist through the Society of Plastic Engineers. Tom serves on the Oklahoma Section Board as Councilor, is also the past president of the local Oklahoma SPE Section, and as well serves on the SPE Injection Molding Division board.
Joseph Lawrence, Ph.D. Senior Director and Research Professor University of Toledo
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Dr. Joseph Lawrence is a Research Professor and Senior Director of the Polymer Institute and the Center for Materials and Sensor Characterization at the University of Toledo. He is a Chemical Engineer by training and after working in the process industry, he has been engaged in polymers and composites research for 18+ years. In the Polymer Institute he leads research on renewably sourced polymers, plastics recycling, and additive manufacturing. He is also the lead investigator of the Polyesters and Barrier Materials Research Consortium funded by industry. Dr. Lawrence has advised 20 graduate students, mentored 8 staff scientists and several undergraduate students. He is a peer reviewer in several journals, has authored 30+ peer-reviewed publications and serves on the board of the Injection Molding Division of SPE.
Matt Hammernik Northeast Account Manager Hasco America
A Resin Supplier’s Perspective on Partnerships for the Circular Economy
About the Speaker
Matt Hammernik serves as Hasco America’s Northeast Area Account Manager covering the states Michigan, Ohio, Indiana, and Kentucky. He started with Hasco America at the beginning of March 2022. Matt started in the Injection Mold Industry roughly 10 years ago as an estimator quoting injection mold base steel, components and machining. He advanced into outside sales and has been serving molders, mold builders and mold makers for about 7 years.
84 countries and 85.6k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Need help from SPE Headquarters?
SPE HQ provides a range of services to Chapters. If you are a chapter and need HQ services (i.e.,
event registration - full list of HQ services can be found here), please fill out and submit the HQ services request form found
here: www.4spe.org/HQservices.
IMPORTANT! If you are simply looking to post your
event on SPE's calendar, please click the "Submit an Event" button below. All events
submitted for inclusion in the SPE calendar are subject to approval.
Going to a SPE event?
If you are going to a SPE event and need a Visa invitation letter, please submit your request for a Visa Invitation letter.
SPE Members receive discounted rates on all event registrations. Not a member of SPE? Join today!
How to reference articles from the SPE Library:
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers, ISBN: 123-0-1234567-8-9, pp. 000-000.
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
